In stock
$49.95
Choose options

Latest reviews

Tuesday 02 March, 2021
The "DAA Die Assembly" (in 9mm) is well made and works flawlessly on my XL750. I will picking up the 40 S&W and 45 ACP versions soon.
Rating: (5 of 5 Stars!)
Monday 22 February, 2021
I have always been an RCBS and Hornady machine user, just what I started with and have gotten comfortable. As such I didn't often venture too far from RCBS, LEE, Hornady or Redding for my dies and accessories. After spending $200 on failed bullet feeders from RCBS and Hornady I stumbled on Mr...
Rating: (5 of 5 Stars!)
Tuesday 16 February, 2021
I'm placing them on my Dillon tool heads and using the feeding tubes for the bullets. One for 38 super comp. One for standard 38 super. Two for 9mm. One for 40 s&w.
Rating: (5 of 5 Stars!)
Saturday 13 February, 2021
It just works every time regardless of bullet type. Lead, jacketed, or powder coated this die works flawlessly every load every time.
Rating: (5 of 5 Stars!)
Wednesday 10 February, 2021
Purchased the 9mm/38S, the .40SW and the .45 have only had the opportunity to use the 9mm/38S model so far. Each size is identical with the exception of the inside tube's ID it seems to me. Once installed and adjusted properly, the 9mm performed flawlessly. Am very satisfied with this MBF...
Rating: (5 of 5 Stars!)
Monday 01 February, 2021
Haven't used the bullet feeders before , so I bought the feeder die to try and it works better than I expected. Was easy to set up and just sets a single bullet on the case .
Rating: (5 of 5 Stars!)
Thursday 28 January, 2021
Loaded a lot of rounds in 9mm , 40cal, 10mm and 45. Excellent tool.
Rating: (5 of 5 Stars!)
Thursday 14 January, 2021
I added this to my Dillon RL1100 and it works great. It's much easier for me to drop the bullets into the top of the die then set each one on the case. The die will hold three or four bullets (9 mm) so it does speed things up. I just ordered the mini feeder to go with the die.
Rating: (5 of 5 Stars!)
Monday 04 January, 2021
It was easy to install and set up. It runs smoothly without any problem.
Rating: (5 of 5 Stars!)
Tuesday 29 December, 2020
By far the most reliable, trouble-free bullet feeding die I have used. I struggled regularly with the Hornady bullet feeding die, so was prepared to do battle with DAA's die to get it to work. I had problems initially, but then actually took a couple of minutes to read the instructions. Once I...
Rating: (5 of 5 Stars!)
Wednesday 02 December, 2020
Excellent product, works well, easy to adjust. Will work alone or with other multiple bullet feed devices. There will be problems with XL750 machines; the Dillon powder measure charge bar is too long and no small bar has been developed to throw over 20-21 grains of powder. Beyond that, this is a...
Rating: (5 of 5 Stars!)
Monday 30 November, 2020
Great product don’t know how I got along with out it. I would suggest it to anyone.
Rating: (5 of 5 Stars!)
Wednesday 18 November, 2020
Super produit, jamais de problème de distribution d'ogives. Facilement réglable.
Rating: (5 of 5 Stars!)
Tuesday 20 October, 2020
This works like a charm with one exception...when reloading lead cowboy action bullets which have a lot of lube on them, this will need to be removed periodically and cleaned or it will drop multiple bullets.

For 9mm copper jacketed, it functions perfectly every time.
Rating: (5 of 5 Stars!)
Thursday 15 October, 2020
Awesome system! Works perfectly with my Dillon 650XL.
Rating: (5 of 5 Stars!)
Thursday 08 October, 2020
These are the best bullet feeder dies made, put all else to shame. I've used these hundreds of times without 1 mix, have all 3 calibers.
Rating: (5 of 5 Stars!)
Thursday 17 September, 2020
Great gear, had one for .40, needed one in 9mm.. easy install and setup.
Rating: (5 of 5 Stars!)
Monday 07 September, 2020
These bullet feed dies are the best made! Easily drops lead and jacketed bullets without issue. I've tried the Lee, RCBS, and Hornady systems, and all have problems. Save yourself time and $$, just purchase the MBF dies.
Rating: (5 of 5 Stars!)
Thursday 27 August, 2020
Love the Mr. BulletFeeder die! For a year, I used the Hornady bullet feeder die with mixed results. Every time I got ready to use the Hornady die, it seemed I had to re-calibrate it. Frustrated With the erratic results, I finally switched to the Mr. BulletFeeder Die and haven’t looked back! Thank...
Rating: (5 of 5 Stars!)
Tuesday 11 August, 2020
The best darn bullet die i have used!Easy to set up,maybe five minute,works every time.A little costly but well worth it.I don't think you can go wrong with this die.
Rating: (5 of 5 Stars!)

Mr.BulletFeeder by DAA Die Assembly Only

(107)
Manufacturers: Double-Alpha Academy

Description:

The Mr.BulletFeeder die assembly is the “clever” part of the Dropper, the  part that allows only one bullet to drop while retaining the rest of the stack.

Made of Anodized Aluminum, this assembly  is caliber specific and includes a threaded die body, an inner aluminum dropper tube, a nut, clip and 3 steel balls.

This assembly is the same item used for both the Mr.Bulletfeeder and the Mini Mr.Bulletfeeder by DAA.

These Die assemblies are sold separately, to enable you to set up a 2nd tool head, leaving the die correctly adjusted on each. If similar calibers are in use, such as 9mm on one toolhead and 38 on a 2nd, you can transfer the upper part of the dropper from one to the other, leaving only the die on the dedicated tool head, permanently adjusted. This will save you buying a complete new dropper for the 2nd caliber, and also mitigate the need to detach the wiring and the feed spring from the top of the dropper assembly as you switch over calibers..

Reviews (107)

Tuesday 02 March, 2021
The "DAA Die Assembly" (in 9mm) is well made and works flawlessly on my XL750. I will picking up the 40 S&W and 45 ACP versions soon.
Monday 22 February, 2021
I have always been an RCBS and Hornady machine user, just what I started with and have gotten comfortable. As such I didn't often venture too far from RCBS, LEE, Hornady or Redding for my dies and accessories. After spending $200 on failed bullet feeders from RCBS and Hornady I stumbled on Mr Bullet in a Dillon thread and boy am I glad that I did. I now have all four or my progressive presses setup running Mr Bullet and it NEVER fails. The worst that will happen is a double drop and a simply raise of the die will resolve this for good. This can happen if you set with just a few bullets and then run a complete tube in production mode. The design is so simple but so very effective. A spring is a good add and helps it return each time. I use a 2" long x 1/8" diameter fairly week spring connected at both ends on the retainer clip stretched downward onto a short machine screw threaded into the side of an RCBS lock nut threaded onto the die above the original that locks to the die plate. Super simple, clean and does the job. Mr Bullet has an add-on that is dual spring and probably better as it would apply even pressure on the inner die tube. I especially love how I can easily switch over calibers and run the same bullet drop die especially with the 9mm, 380, 38s and 357 mag. The dies are very reasonably priced so having one for everything you do is not a problem. And you don't need a bullet tube array for everything you do just move it around as needed if you run multiple setups as I do. 100% support for Mr BulletFeeder. What a great product.
Tuesday 16 February, 2021
I'm placing them on my Dillon tool heads and using the feeding tubes for the bullets. One for 38 super comp. One for standard 38 super. Two for 9mm. One for 40 s&w.
Saturday 13 February, 2021
It just works every time regardless of bullet type. Lead, jacketed, or powder coated this die works flawlessly every load every time.
Wednesday 10 February, 2021
Purchased the 9mm/38S, the .40SW and the .45 have only had the opportunity to use the 9mm/38S model so far. Each size is identical with the exception of the inside tube's ID it seems to me. Once installed and adjusted properly, the 9mm performed flawlessly. Am very satisfied with this MBF product. DAA's rapid restocking and shipping was excellent as well.
Monday 01 February, 2021
Haven't used the bullet feeders before , so I bought the feeder die to try and it works better than I expected. Was easy to set up and just sets a single bullet on the case .
Thursday 28 January, 2021
Loaded a lot of rounds in 9mm , 40cal, 10mm and 45. Excellent tool.
Thursday 14 January, 2021
I added this to my Dillon RL1100 and it works great. It's much easier for me to drop the bullets into the top of the die then set each one on the case. The die will hold three or four bullets (9 mm) so it does speed things up. I just ordered the mini feeder to go with the die.
Monday 04 January, 2021
It was easy to install and set up. It runs smoothly without any problem.
Tuesday 29 December, 2020
By far the most reliable, trouble-free bullet feeding die I have used. I struggled regularly with the Hornady bullet feeding die, so was prepared to do battle with DAA's die to get it to work. I had problems initially, but then actually took a couple of minutes to read the instructions. Once I followed the simple set-up process, the die began working without issue.
The one caveat I would offer - the die is made of aluminum, so be gentle with it. It is certainly robust enough to do its job, but do be careful installing it (as you should with all dies, really).
Wednesday 02 December, 2020
Excellent product, works well, easy to adjust. Will work alone or with other multiple bullet feed devices. There will be problems with XL750 machines; the Dillon powder measure charge bar is too long and no small bar has been developed to throw over 20-21 grains of powder. Beyond that, this is a very handy device.
Monday 30 November, 2020
Great product don’t know how I got along with out it. I would suggest it to anyone.
Wednesday 18 November, 2020
Super produit, jamais de problème de distribution d'ogives. Facilement réglable.
Tuesday 20 October, 2020
This works like a charm with one exception...when reloading lead cowboy action bullets which have a lot of lube on them, this will need to be removed periodically and cleaned or it will drop multiple bullets.

For 9mm copper jacketed, it functions perfectly every time.
Thursday 15 October, 2020
Awesome system! Works perfectly with my Dillon 650XL.
Thursday 08 October, 2020
These are the best bullet feeder dies made, put all else to shame. I've used these hundreds of times without 1 mix, have all 3 calibers.
Thursday 17 September, 2020
Great gear, had one for .40, needed one in 9mm.. easy install and setup.
Monday 07 September, 2020
These bullet feed dies are the best made! Easily drops lead and jacketed bullets without issue. I've tried the Lee, RCBS, and Hornady systems, and all have problems. Save yourself time and $$, just purchase the MBF dies.
Thursday 27 August, 2020
Love the Mr. BulletFeeder die! For a year, I used the Hornady bullet feeder die with mixed results. Every time I got ready to use the Hornady die, it seemed I had to re-calibrate it. Frustrated With the erratic results, I finally switched to the Mr. BulletFeeder Die and haven’t looked back! Thank you DAA!
Tuesday 11 August, 2020
The best darn bullet die i have used!Easy to set up,maybe five minute,works every time.A little costly but well worth it.I don't think you can go wrong with this die.
You may also be interested in