DAA Mini Mr. Bulletfeeder - Pistol

Double-Alpha Academy
Configure
Caliber
$159.95
Save for Later
(90)
 Item in Stock | Usually dispatched within 24 hours

Latest reviews

DOUG ***
Thursday 08 February, 2024
Combo :Mini Mr Bullet Feeder pistol and 2-in1 seating and crimping die

I bought this after hesitating to do so for some time, not being certain that I really needed it. After much more fumbling when trying to pick up short and slippery 9mm round nose bullets, to place on the flared casing in the...
Rating: (2 of 5 Stars!)
Brad ***
Tuesday 21 March, 2023
I bought this to load 44-40. Tried to use my regular 44 cal powder funnel in a Dillon 550B with case feeder. No joy. .427" bullet RNFP powder coated. Internal balls in die kept catching lube groove. Solution was to sacrifice an extra Dillon 45 cal powder funnel to the lathe and duplicate the...
Rating: (5 of 5 Stars!)
Neil ***
Tuesday 14 March, 2023
Great! Had one minor failure to drop in 500 rounds with 124gr lead bullets. It took less than 5 minutes to get the right adjustment set. Compare that with my hornady bullet feeder which would experience a problem every 10 or 20 rounds. The DAA is a no-brainer, wish I had not wasted $$ on the...
Rating: (5 of 5 Stars!)
Michael ***
Saturday 31 December, 2022
I purchased this along with the DA Dillon Extra-Short powder bar to load 9mm on my Dillon 750XL. Together they are worth every penny and I'm kicking myself for not buying them sooner! The products are well designed and the setup was a breeze. Once I started loading I was shocked at how well the...
Rating: (5 of 5 Stars!)
Pete ***
Saturday 02 April, 2022
Over all this works very well and has increased the speed that I can reload dramatically. The only complaint is that occasionally the alignment is not perfect when I rotate the tube to the next column of bullets. I'll rotate, they drop but after a few bullet drops, they are hung up in the tube...
Rating: (4 of 5 Stars!)
John ***
Saturday 05 February, 2022
Got the Mini Mr Bullet Feeder for pistols a few weeks ago and it’s been the best addition to my Hornady LnL setup ever! Initially I had problems loading the smaller 100gr bullets (double drops), but Customer Support suggested moving the ball bearings and clip to the bottom setting and everything...
Rating: (5 of 5 Stars!)

Description:

Please be aware of the following:

The Dillon XL750 Powder Measure is angled such that the powder bar must extend directly over station #4 in the toolhead, and it cannot be repositioned. This Is not an issue if you have a short die in that station. However, if you wish to run a powder check in station #3, and a bullet dropper in station #4, as many do, this creates a serious problem.

As a solution to this  issue we are pleased to offer our Extra-Short Dillon Powder Bar.

Based on the success of the Mr. Bullet Feeder by DAA, DAA has now launched a new more economical version of the original Mr. Bullet Feeder.  The new Mini Mr. Bullet Feeder by DAA uses a 6-tube magazine system which holds roughly 100 bullets. It feeds into the same reliable dropper die assembly as used on the Mr.Bulletfeeder by DAA.

Each magazine of bullet tubes needs to be manually filled by hand before reloading begins, similar to the way a primer tube is filled before starting the reloading process. After a little practice, it will take approximately 2 minutes to fill the tube assembly. This can be done in advance of the reloading process to save time.  Additional tube assemblies can be purchases separately (or as a bundle), thus allowing you to pre-load 300, 400 or more bullets before starting a reloading session.

While reloading, the bullets will drop down in the transparent tube, as they feed into the dropper-die assembly. Once a tube is empty, you simply rotate and click the next tube into place and keep reloading. Transition to the next tube takes just a second or two. Once the entire 6-tube magazine is empty, either reload it by hand, or drop your 2nd assembly into place to continue reloading without delay.

The Mini Mr.Bulletfeeder by DAA can be used on any progressive reloading machine which uses the same size dies as Dillon, however please note that the powder funnel supplied with the Mini Mr.Bulletfeeder by DAA is designed to be used ONLY in the Dillon powder drop! If you wish to use the Mini Mr.Bulletfeeder by DAA with another press, you may need to purchase elsewhere another powder funnel to expand the brass.

NOTE: That the bullet feeder does require a station on the tool head, direcly after the powder dropper.

DAA has found it is difficult to use the Mini Mr.Bulletfeeder on a 1050 when a powder check is being used in the following station. This has to be with the angle in which the powder dropper sits, forcing the bullet dropper to rotate further away, over the next station. This is an issue only on a 1050

The Mini Mr. Bulletfeeder includes:

1 x 6-Tube Bullet Magazine Assembly
1 x Dropper Die Assembly
1 x Expanding powder funnel (Dillon compatible)
3 x Spare Steel Ball-Bearings for Dropper
1 x User Instruction Sheet

Please note: Mr.Bullet feeders and Mini Mr.BF are usually shipped with our Dillon Powder funnel. If you wish us to swap that out for a Hornady funnel when shipping – we can do so for you - request that at time of ordering. Or, separately purchase your Hornday expanding powder funnel here

Click here for user instructions for this and other products.

General questions

Q: Will the mini Mr. Bullet Feeder work with lead cast, polymer coated bullets? Specifically .40 cal. (.401 diameter)?

Yes, as long as they are not full wadcutters.

Q: I would like to know if your mini...

We Also Recommend
(31)
Important Note
$56.95
$1.00 Reward points
Also Available In Set(s)

New Products

Important Note
$16.00
$1.00 Reward points
(3)
Important Note
$12.95
Important Note
$68.95
$2.00 Reward points
(1)
Important Note
$79.95
$2.00 Reward points
(3)
Important Note
$15.95
$1.00 Reward points