Mini Mr.BulletFeeder by DAA - Rifle

Double-Alpha Academy
$3.00 Reward points
Save for Later
 Item in Stock | Usually dispatched within 24 hours

Latest reviews

Bryan Leist ***
5 Nov 2023
The Mini runs perfect and I have no Issues.
Rating: (5 of 5 Stars!)
James ***
24 Jun 2023
I am a big fan of the mini Mr Bullet Feeder, I have both rifle and pistol holders and have used both extensively. A comment about the .223 bullet holder if you are planning to use bigger bullet weights (above 55g) depending on the manufacturer of the bullets some of them may get stuck in the tube...
Rating: (3 of 5 Stars!)
Scott ***
17 Mar 2022
This thing just works. Perfect. Simple and efficient. Very happy and would recommend to anyone
Rating: (5 of 5 Stars!)
Brian ***
17 Dec 2021
This works extremely well. I plan to order one for 9mm as well.
Rating: (5 of 5 Stars!)
Richard ***
3 Sep 2021
Great price, easy on the budget, holds 100 + bullets setup in a few minutes. recommend this product. I also have DAA 9mm bulletfeeder.
Rating: (5 of 5 Stars!)
George ***
28 Jul 2021
Reasonable price for what it does, easy to install in place of the powder check, holds over 100 bullets at a time, and does the job ! What more could you ask? Recommended !!
Rating: (5 of 5 Stars!)


Please be aware of the following:

The Dillon XL750 Powder Measure is angled such that the powder bar must extend directly over station #4 in the toolhead, and it cannot be repositioned. This Is not an issue if you have a short die in that station. However, if you wish to run a powder check in station #3, and a bullet dropper in station #4, as many do, this creates a serious problem.

As a solution to this  issue we are pleased to offer our Extra-Short Dillon Powder Bar.

As of Feb 2021 we are transitioning to using longer Rifle insert tubes in order to hold even more bullets in the tube magazine. We are extending the tubes by approx.. 6 inches.
For Dillon 1050 users the tubes will need to be shortened by the user! As they will not fit in beneath the case feeder.

The Rifle Mini Mr.Bulletfeeder by DAA uses a 6-tube magazine system which holds roughly 70-100 bullets, depending on bullet caliber and length. It feeds into the same brilliantly reliable dropper die assembly as used on the Mr.Bulletfeeder

Using a Bulletfeeder while reloading is a real pleasure. It makes the reloading process faster and much easier. If you have never used one, you are missing out on one of the greatest reloading assists out there! A Bulletfeeder also improves safety, by preventing the need to insert your fingers under the tool head to place your bullets on the brass. Everyone should use one! 

Each magazine of bullet tubes needs to be filled by hand before reloading, much in the same way you would fill your primer tubes before starting your reloading session. With a little practice, it will take you about 2 minutes to fill the tube assembly. And this can be done in advance while watching TV in the comfort of your living room. Additional tube assemblies can be purchases separately (or as a bundle), thus allowing you to pre-load 300, 400 or more bullets before starting your reloading session. 

While reloading, you will see the bullets drop down in the transparent tube, as they feed into the dropper-die assembly. Once a tube is empty, you simply rotate and click the next tube into place and keep reloading. Transition to the next tube takes just a second or two. Once the entire 6-tube magazine is empty, either reload it by hand, or drop your 2nd assembly into place to continue without delay. 

The Mini Mr.Bulletfeeder can be used on any progressive reloading machine which uses the same size dies as Dillon. Be aware that the bullet feeder does require a station in your tool head, directly after the powder dropper. 

We have found it is difficult to use the Mini Mr.Bulletfeeder on a 1050 when a powder check is being used in the following station. This has to do with the angle in which the powder dropper sits, forcing the bullet dropper to rotate further away, over the next station. This is an issue only on a 1050. 

Your Rifle Mini Mr.Bulletfeeder by DAA includes:

1 x 6-Tube Bullet Magazine Assembly

1 x Dropper Die Assembly

3 x Spare Steel Ball-Bearings for Dropper

1 x User Instruction Sheet 


No expanding powder funnel is included with this system, because throating the rifle brass in the powder funnel is not possible. That would lead to too small a powder through hole. Flaring the brass must be done as a prep stage or using a modified M-die on the 1050.

We Also Recommend
Important Note
$2.00 Reward points
Also Available In Set(s)

New Products

Important Note
Important Note
$2.00 Reward points