Wednesday 17 August, 2022
Works great, the additional step on the powder funnel allows for perfect bullet placement prior to seating and crimping.
Tuesday 26 July, 2022
I’ve run in excess of 25,000 rounds and it didn’t work as it did when new, so I replaced it.
Monday 28 March, 2022
Works perfectly for the Mr. Bullet feeder than the original Dillon funnel. The original funnel either over flare or not flare enough for bullet stabilization as it drop and seat on the casing. This will solve the problem. But you will have to reset the powder measure completely.
Monday 07 February, 2022
Works perfectly! I recommend it, I use it with bullet feeder, however I think it will be useful even with manual bullet feed - bullets re reliably holding in place.
Sunday 10 October, 2021
The one got (9MM) had some corrosion inside it. I ran a strip of emery cloth through it and a brass bore brush which improved it.
The belling of the case was far better than the standard Dillon funnel and the longer taper sped up powder fall.
I would recommend it.
Sunday 26 September, 2021
The DAA powder funnel for Dillon presses is truly amazing. I will be surprised if DP does not copy them. Bullets don't fall off when the case rotates on my 750. Great value and even greater design.
Monday 20 September, 2021
Even though I am not going to use with the Mr.Bulletfeeder as I don't load that much to need it. But for 9mm it make the bullet seat so much better so there is no Lead scraping as you seat the head into the case . it also sits there so not pinching your fingers into the dies lol very well done DAA
Sunday 12 September, 2021
Fantastic, bullet alignment is much easier while reloading.
Sunday 27 June, 2021
The DAA powder funnel works really well. The standard Dillon 9mm powder funnel does not bell the 9mm caseneck enough. After fitting the DAA 9mm funnel to my Dillon 750, bullets no longer fall out when the press indexes. GREAT product that works. The Mr BulletFeeder itself is also AMAZING. It saves time and work and REALLY SPEEDS UP cartridge output. I am a VERY SATISFIED customer. Grahame Clifford. Tumbi Umbi. AUSTRALIA.
Friday 25 June, 2021
This has fixed my problem of the bullets not seating well when the shell plate rotates! This is a must have for reloading!
Wednesday 07 April, 2021
Works very well, does what it said would do I recommend this for any Dillon dies on any press that you use
Monday 22 March, 2021
Seats the bullet perfectly. I use the Redding special bell die on my turret press. Basically does the same thing.
Tuesday 09 March, 2021
Works great with the bullet feeder! Gotta have it!
Tuesday 15 December, 2020
More gradual taper than Dillon. Worked better for me on 9MM & .38.
Wednesday 02 December, 2020
Great product for any shooter wanting to load large quantities of ammunition.
Sunday 08 November, 2020
These powder funnels are a must for coated bullets. After having 10-12 no drop test pieces per 100 with a generous flare (0.020 over). I switched to the stepped powder funnel. The lead shaving was eliminated with less flare. The no drops per 100 was less than 2 and those still chamber. What I found was the bullets would tip sideways going up into the seating die. Causing case deformation which cause most of my problems. PLEASE MAKE MORE SIZES 458 AND 30 CAL BULLETS NEED THESE TOO.
Wednesday 16 September, 2020
Bells the case mouth perfectly but sticks in the case causing an annoying “thump” and powder spillage on retraction. I tried lubed and non-lubed cases. I even tried lubing the powder funnel.
Thursday 30 April, 2020
Sembra fatto molto bene, da un’idea di solidità nel tempo !!
Tuesday 24 March, 2020
Love the way this funnel works,,,So well in fact that I ordered the Mini bullet feeder to go with it..
Wednesday 19 February, 2020
Works great with powder drop . No problems with brass sticking to funnel. I find myself using your site to purchase Dillon products.