Saturday 19 September, 2020
this works very well, simple to use. combine it withe the feeder bowl and I don't need a $300 case feeder.
Tuesday 31 March, 2020
It is very well made and was extremely easy to install on my Dillon 750 and works just like the Dillon case feeder (I have both). If you are looking for a case feeder I would not hesitate to purchase this.
Friday 27 March, 2020
Works great, I was going to use this until I could afford a case feeder but I may just save my money and keep using this mini case feeder.
Sunday 08 March, 2020
Best $55 spent in a new accessory for reloading. So simple and I can’t believe it’s at this price point!!!
Friday 20 December, 2019
I went with this case feeder because I couldn't justify the cost of a Dillon case feeder versus my planned output. I tend to load in batches of 100 or 200... The feeder works as advertised. I had to sand inside of the support ring a bit to fit the adapter tube but that was easy. Takes about 10 minutes to load a tube with 100 cases. Overall, I am extremely pleased with the Mini Case Feeder and the extra Tube Assembly. If I really want a high output reloading session, I can fill both up with 150 cases a piece and go to town. I don't regret not spending the money on Dillon's Case Feeder at all.
I would like to see a collator of some sort. I know they are not perfect, but there are hacks out there that work 99% of the time and I can handle the 1%... Just sayin'...
Tuesday 10 December, 2019
I've bought 2 of these to use on a manual roll sizer unit. It works great without having to buy an automatic case loader for which I do not have the room for.
Monday 04 November, 2019
This case feeder is a nifty quiet addition to my 750XL it works for many calibers.. not sure there's any it doesn't work with.I have not found any. I also use a lee quad rotating case loader with collator It would be nice to see DAA team develop this with a shaker collator on top I prefer over filling the tubes any day..A must have for us automated people. I have the Dillon automatic case feeder on my 650XL it's just so noisy. I picked up a few to keep each caliber set up complete. a slight modification was required to get it to stay mounted on the bolt at the case feeder housing..It works as designed
Friday 25 October, 2019
I purchased this Mini Case Feeder for my 650 because $300 is too much for the Dillon case feeder. I wasn’t expecting it to work as well as it did to tell you the truth. I was so pleased after the first use, I immediately bought another feeder. During the loading session, when i’m using the one feeder, I have my son filling the other. You can load 500 rounds in no time. I did have to sand down the adapter a bit to get it to fit onto my press, but besides that, the installation was simple. I am pleased with DAA products, and I would recommend them to anyone with a Dillon loading machine.
Wednesday 18 September, 2019
Love this case feeder..allows me to load 66 223 cases with refill. Simple design, no motors, no noise, very economical alternative to motorized case feeder. I want a spare set of tubes!
Wednesday 04 September, 2019
Easy to install and takes up less space then a auto feeder.
I fill the tubes when waching TV :-)
Will order a spare tube soon.
Reinier de Jong
Wednesday 30 January, 2019
Works great on my Dillon 650, I have no issues with it and it’s a good less expensive alternative
Wednesday 12 December, 2018
great inexpensive solution at 1/5th the price of a dillon unit and 1/4 the size ... i purchased one for 9mm and .40s&w and the tubes are interchangable so its even more usefull
and prep is no diffrent then loading primer tubes ... load up the tubes then just run till they are empty
Saturday 11 August, 2018
Fantastic Product that lends itself to be even more versatile! While not want a full size case feeder, I needed something to improve my process for loading 9mm. Enter the mini XL650 vase feeder, allowing me to have 150 cases pre-loaded and ready to go! Then I wondered could this product do even more then it's initial design? Being that several case feed parts of my Dillon XL650 are shared between 9mm, 223/5.56 and 300 BO, could this be used for 223/5.56 and 300 BO as well? So I dropped in some 223/5.56 and 300 BO into the mini XL650 case feeder and with a small amount of painters masking tape on the fitting to hold to the appropriate Dillon case feeder, I can now utilize the product to load 9mm, 223/5.56 and 300 BO. Amazing, 1 product that meets 3 of my reloading needs! Great job in designing an excellent and modifiable product to meet varying needs of reloader's everywhere! I plan on an additional purchase so I can make a more permanent modification for 223/5/56 and 300 BO.
Tuesday 05 June, 2018
Perfect tool for us that don't want or need a full size casefeeder.
Friday 20 April, 2018
Excellent product. I am very satisfied. Good! good! good!
Sunday 28 January, 2018
This xl650 mini case feeder is super fantantic,I wish the mini case feeder for 45acp comes very soon,Thank you DAA
Wednesday 17 January, 2018
Excellent product, except bottom plastic piece broke off in about 2 weeks. Still works fine.
Friday 29 December, 2017
Facile a monter et apporte un confort pour la distribution des etuis sur ma xl650.
Coupler avec Mr Bullet Feeder gain de temps assurer.
Une altermative a la distribution avec un case feeder.
Thursday 28 December, 2017
This Mini Case Feeder is a fantastic add-on for the Dillon 650XL giving a good capacity and speed for the reloading job!
Saturday 25 November, 2017
The mini case feeder is awesome. Easy to install on my XL650 Dillon. The first time I put out 300 rounds in no time. I plan on purchasing the mini bullet feeder just for my 9mm rounds. Just not sure about being able to check the amount of powder that dropped. I highly recommend this product. I also purchased the spare tube. Now if only DAA would somehow increase the amount of primers in the Dillon.
Great Job, great company.