DAA Mini Mr. Bulletfeeder - Pistol

Double-Alpha Academy
Configure
Caliber
$159.95
Save for Later
(90)
 Item in Stock | Usually dispatched within 24 hours

Latest reviews

Gordian ***
Sunday 10 January, 2021
Simple to set up and works as discribed on my Hornady LNL Press. Tested with 9mm Flatpoints, Roundnose, Hollowpoints.
Rating: (5 of 5 Stars!)
Joseph ***
Sunday 13 December, 2020
A very reliable bullet feeder solution. I had to get the short charge bar to use with my Dillon 750 as I have the powder check station installed, but after that I have found this to be a trouble free system. The bullet dropper reliably drops a single bullet even when the stack is running out. I...
Rating: (5 of 5 Stars!)
Bruce ***
Thursday 10 December, 2020
The most bang for the buck product I have purchased in awhile. This works great was easy to install and has tripled my production of ammo.
Rating: (5 of 5 Stars!)
Dale ***
Tuesday 01 December, 2020
I love this bullet feeder. It's perfect for the type of reloading I do. I much better alternative to it's much larger model. I use it for making .380 rounds and it holds about 125, 100gr bullets. The tubes that hold the bullets are made from decent gauge plastic, so it's very sturdy. Now, if I...
Rating: (5 of 5 Stars!)
Patrick ***
Thursday 12 November, 2020
This makes my reloading sessions more productive. It works perfectly and it was easy to install.
Rating: (5 of 5 Stars!)
JOHN ***
Thursday 12 November, 2020
When I decided that I wanted to use a bullet feeder, I researched both Lee and Mr. Buller Feeder. My research showed me that Mr. Bullet Feeder would feed the bullets from the top down (as opposed to from the side) that made more sense to me. I didn't want to spend close to $500 for the automatic...
Rating: (5 of 5 Stars!)

Description:

Please be aware of the following:

The Dillon XL750 Powder Measure is angled such that the powder bar must extend directly over station #4 in the toolhead, and it cannot be repositioned. This Is not an issue if you have a short die in that station. However, if you wish to run a powder check in station #3, and a bullet dropper in station #4, as many do, this creates a serious problem.

As a solution to this  issue we are pleased to offer our Extra-Short Dillon Powder Bar.

Based on the success of the Mr. Bullet Feeder by DAA, DAA has now launched a new more economical version of the original Mr. Bullet Feeder.  The new Mini Mr. Bullet Feeder by DAA uses a 6-tube magazine system which holds roughly 100 bullets. It feeds into the same reliable dropper die assembly as used on the Mr.Bulletfeeder by DAA.

Each magazine of bullet tubes needs to be manually filled by hand before reloading begins, similar to the way a primer tube is filled before starting the reloading process. After a little practice, it will take approximately 2 minutes to fill the tube assembly. This can be done in advance of the reloading process to save time.  Additional tube assemblies can be purchases separately (or as a bundle), thus allowing you to pre-load 300, 400 or more bullets before starting a reloading session.

While reloading, the bullets will drop down in the transparent tube, as they feed into the dropper-die assembly. Once a tube is empty, you simply rotate and click the next tube into place and keep reloading. Transition to the next tube takes just a second or two. Once the entire 6-tube magazine is empty, either reload it by hand, or drop your 2nd assembly into place to continue reloading without delay.

The Mini Mr.Bulletfeeder by DAA can be used on any progressive reloading machine which uses the same size dies as Dillon, however please note that the powder funnel supplied with the Mini Mr.Bulletfeeder by DAA is designed to be used ONLY in the Dillon powder drop! If you wish to use the Mini Mr.Bulletfeeder by DAA with another press, you may need to purchase elsewhere another powder funnel to expand the brass.

NOTE: That the bullet feeder does require a station on the tool head, direcly after the powder dropper.

DAA has found it is difficult to use the Mini Mr.Bulletfeeder on a 1050 when a powder check is being used in the following station. This has to be with the angle in which the powder dropper sits, forcing the bullet dropper to rotate further away, over the next station. This is an issue only on a 1050

The Mini Mr. Bulletfeeder includes:

1 x 6-Tube Bullet Magazine Assembly
1 x Dropper Die Assembly
1 x Expanding powder funnel (Dillon compatible)
3 x Spare Steel Ball-Bearings for Dropper
1 x User Instruction Sheet

Please note: Mr.Bullet feeders and Mini Mr.BF are usually shipped with our Dillon Powder funnel. If you wish us to swap that out for a Hornady funnel when shipping – we can do so for you - request that at time of ordering. Or, separately purchase your Hornday expanding powder funnel here

Click here for user instructions for this and other products.

General questions

Q: Will the mini Mr. Bullet Feeder work with lead cast, polymer coated bullets? Specifically .40 cal. (.401 diameter)?

Yes, as long as they are not full wadcutters.

Q: I would like to know if your mini...

We Also Recommend
(31)
Important Note
$56.95
$1.00 Reward points
Also Available In Set(s)

New Products

(3)
Important Note
$12.95
Important Note
$68.95
$2.00 Reward points
(2)
Important Note
$15.95
$1.00 Reward points
Important Note
$79.95
$2.00 Reward points
Important Note
$26.95
$1.00 Reward points