Mini Mr.BulletFeeder by DAA - Rifle

Double-Alpha Academy
Configure
Caliber
$129.95
Save for Later
$3.00 Reward points
(39)
 Item in Stock | Usually dispatched within 24 hours

Latest reviews

Mr. ***
Friday 10 November, 2017
Hands down the best setup I've used. I have several Hornady feeder dies and what a difference. I wish that I had never bought anything but the DAA feeder. Setup was under 5 minutes their was zero tweaking and BT bullets never fall off the cases once loaded. ***** 5 STARS *****
Rating: (5 of 5 Stars!)
Eric
Wednesday 06 September, 2017
Simple but a great addition to the reloading process. While some have an issue with the feeder assembly price, I think the engineering and quality of the feeder justifies the cost. Also, one must consider the market for this type of unit, I doubt the company is cranking out thousands of these...
Rating: (5 of 5 Stars!)
Barry ***
Sunday 06 August, 2017
The Mini Mr. Bullet Feeder is an excellent concept. Reasonably priced and works exactly as described. I now use them for 9MM, 45 ACP and 223. Double Alpha's Customer Service is also outstanding. I had a couple of questions and received a response within an hour. Great products. Great service.
Rating: (5 of 5 Stars!)
Rich
Sunday 06 August, 2017
Works brilliantly just a pity the bullet collator is so expensive, as I have forgotten to keep an eye on the tubes and missed a few cases as this really does speed the process up, now currently building my own collator then this will be awesome
Rating: (4 of 5 Stars!)
Izak ***
Sunday 28 May, 2017
reloading 223REM is now only a pleasure with the mini bullet feeder
work perfectly on the Hornady LNL
very good buy, even with our current exchange rate in South Africa
Rating: (4 of 5 Stars!)
Robin ***
Wednesday 17 May, 2017
Bought this for my Dillon 650...talk about easy! Load the projectiles, drop it into the press, and away you go! Every pull completes another round. No trapped fingers! I love it!
Rating: (5 of 5 Stars!)

Description:

Please be aware of the following:

The Dillon XL750 Powder Measure is angled such that the powder bar must extend directly over station #4 in the toolhead, and it cannot be repositioned. This Is not an issue if you have a short die in that station. However, if you wish to run a powder check in station #3, and a bullet dropper in station #4, as many do, this creates a serious problem.

As a solution to this  issue we are pleased to offer our Extra-Short Dillon Powder Bar.

As of Feb 2021 we are transitioning to using longer Rifle insert tubes in order to hold even more bullets in the tube magazine. We are extending the tubes by approx.. 6 inches.
For Dillon 1050 users the tubes will need to be shortened by the user! As they will not fit in beneath the case feeder.

The Rifle Mini Mr.Bulletfeeder by DAA uses a 6-tube magazine system which holds roughly 70-100 bullets, depending on bullet caliber and length. It feeds into the same brilliantly reliable dropper die assembly as used on the Mr.Bulletfeeder

Using a Bulletfeeder while reloading is a real pleasure. It makes the reloading process faster and much easier. If you have never used one, you are missing out on one of the greatest reloading assists out there! A Bulletfeeder also improves safety, by preventing the need to insert your fingers under the tool head to place your bullets on the brass. Everyone should use one! 

Each magazine of bullet tubes needs to be filled by hand before reloading, much in the same way you would fill your primer tubes before starting your reloading session. With a little practice, it will take you about 2 minutes to fill the tube assembly. And this can be done in advance while watching TV in the comfort of your living room. Additional tube assemblies can be purchases separately (or as a bundle), thus allowing you to pre-load 300, 400 or more bullets before starting your reloading session. 

While reloading, you will see the bullets drop down in the transparent tube, as they feed into the dropper-die assembly. Once a tube is empty, you simply rotate and click the next tube into place and keep reloading. Transition to the next tube takes just a second or two. Once the entire 6-tube magazine is empty, either reload it by hand, or drop your 2nd assembly into place to continue without delay. 

The Mini Mr.Bulletfeeder can be used on any progressive reloading machine which uses the same size dies as Dillon. Be aware that the bullet feeder does require a station in your tool head, directly after the powder dropper. 

We have found it is difficult to use the Mini Mr.Bulletfeeder on a 1050 when a powder check is being used in the following station. This has to do with the angle in which the powder dropper sits, forcing the bullet dropper to rotate further away, over the next station. This is an issue only on a 1050. 

Your Rifle Mini Mr.Bulletfeeder by DAA includes:

1 x 6-Tube Bullet Magazine Assembly

1 x Dropper Die Assembly

3 x Spare Steel Ball-Bearings for Dropper

1 x User Instruction Sheet 

 

No expanding powder funnel is included with this system, because throating the rifle brass in the powder funnel is not possible. That would lead to too small a powder through hole. Flaring the brass must be done as a prep stage or using a modified M-die on the 1050.

We Also Recommend
(11)
Important Note
$68.95
$2.00 Reward points
Also Available In Set(s)

New Products

Important Note
$16.00
$1.00 Reward points
(3)
Important Note
$12.95
Important Note
$68.95
$2.00 Reward points
(1)
Important Note
$79.95
$2.00 Reward points
(3)
Important Note
$15.95
$1.00 Reward points